J. Ocean Eng. Technol. Search

CLOSE


J. Ocean Eng. Technol. > Volume 40(4); 2026 > Article
Song, Jung, and Jung: Investigating Passing-Ship-Induced Loads on Moored Ships in Confined Waters Using Computational Fluid Dynamics

Abstract

As environmental regulations from the International Maritime Organization (IMO) become increasingly stringent, the adoption of liquefied natural gas (LNG)-fueled vessels has accelerated, highlighting the need for safe and efficient LNG bunkering infrastructure. To ensure secure simultaneous operations (SIMOPS) during bunkering, it is essential to evaluate the hydrodynamic loads exerted on moored ships by passing vessels in confined waters. This study investigated these interactions using a computational fluid dynamics (CFD) approach. Unsteady Reynolds-Averaged Navier–Stokes simulations with an overset mesh, implemented in STAR-CCM+, were validated against benchmark model test data obtained from the International Conference on Ship Manoeuvring in Shallow and Confined Water. The numerical analysis examined surge, sway, and yaw responses of moored ships, along with free-surface elevations and pressure distributions. Parametric studies systematically explored the effects of passing ship speed, lateral clearance, water depth, and quay wall gap. The results show that hydrodynamic loads increase sharply with higher passing speeds, shallower water depth, and reduced separation distances, while quay wall effects remain relatively minor. These findings demonstrate that moored ship safety is highly sensitive to operational and geometric parameters of passing ships. This research provides quantitative insights for developing practical design and operational guidelines to ensure safe SIMOPS in ports.

1. Introduction

As environmental regulations imposed by the International Maritime Organization (IMO) become increasingly stringent, global interest in vessels powered by environmentally friendly fuels has rapidly increased. In particular, liquefied natural gas (LNG), which can significantly reduce emissions of carbon dioxide (CO2), sulfur oxides (SOx), and nitrogen oxides (NOx), has attracted considerable attention as a marine fuel that offers both environmental and economic benefits. Consequently, the development of LNG bunkering infrastructure and related technologies has become increasingly important. During 2024, LNG bunkering volumes at major ports worldwide increased by as much as fourfold compared with the previous year, reflecting the rapid growth of the LNG bunkering industry. This trend suggests that LNG may serve as a key transitional fuel in future maritime decarbonization strategies (IGU, 2025). In South Korea, efforts have also been made to expand the adoption of LNG-fueled vessels and establish the infrastructure required for a safe and reliable fuel supply. As part of these efforts, the Korea Research Institute of Ships and Ocean Engineering (KRISO) developed and constructed a dedicated 500 m3 LNG bunkering vessel for coastal ships in 2022 (Lee & Jung, 2022). However, following the construction and demonstration of the vessel, there remains a need to establish systematic procedures for bunkering operations and simultaneous operations (SIMOPS). To this end, studies evaluating ship motions and mooring safety during SIMOPS are essential for ensuring safe and efficient bunkering operations (Jung et al., 2020; Jung et al., 2021).
The assessment of mooring safety should consider not only environmental conditions, such as wind, current, and waves, but also interaction effects induced by vessels navigating within the port. The effects of passing ships can generally be classified into two categories: wave-making effects and suction effects. Wave-making effects are primarily generated by disturbances originating from the bow and stern and are represented by Kelvin waves, which consist of transverse and divergent wave systems. Kelvin waves become more pronounced as a vessel advances at higher speeds and propagate over greater distances. In contrast, suction effects arise from the flow field generated around a large vessel moving at low speed, resulting in a reduction of the free-surface elevation through the formation of a drawdown wave. A drawdown wave is generally regarded as a long-period wave with a wavelength comparable to the ship's length and tends to exert a greater influence under low-speed conditions. In particular, the effects of drawdown waves become more pronounced in shallow and confined waters, such as port areas, where large vessels operate at low speeds. With the recent trend towards larger vessel sizes, the influence of passing ships in confined waters has become an increasingly important issue (Pinkster, 2009).
The hydrodynamic loads exerted on a moored ship by a passing vessel can induce excessive ship motions, thereby increasing the risk of collisions with adjacent vessels or quay walls and potentially damaging critical equipment, such as mooring systems and bunkering hoses, used during SIMOPS. In the worst-case scenario, such incidents may lead to major explosions and loss of life. Therefore, it is necessary to evaluate mooring safety by quantitatively estimating the hydrodynamic loads acting on moored ships from major vessels entering and leaving a specific port. Such evaluations can contribute to ensuring the safety of simultaneous operations. Furthermore, accidents can be prevented by establishing reasonable operational regulations regarding the speed, separation distance, and navigation route of passing vessels operating in the vicinity of working ships (Park et al., 2021).
Methods for evaluating the hydrodynamic loads acting on moored ships can generally be classified into experimental and numerical model-based approaches. Remery (1974), Vantorre et al. (2002), Kriebel (2007), Lataire et al. (2009), and Böttner and Kondziella (2022) investigated passing ship effects through model tests conducted under various conditions, including vessel speed, ship size, separation distance between vessels, and relative water depth. In particular, the International Conference on Ship Maneuvering in Shallow and Confined Water (MASHCON), jointly organized by Flanders Hydraulics Research and Ghent University, has provided a wide range of benchmark experimental datasets to facilitate a deeper understanding of ship-to-ship interaction problems in confined waters (Lataire et al., 2011; Zwijnsvoorde et al., 2022). These datasets have been widely used by research institutions for the validation of numerical simulation results. Although model testing is generally regarded as the most reliable method for investigating ship interaction phenomena, it has associated practical limitations, including long testing periods, high costs, and the requirement for large-scale towing tanks. In contrast, numerical simulations offer the advantage of efficiently evaluating a wide range of operational scenarios. Potential-flow-based methods, which neglect fluid viscosity, have been extensively employed because of their high computational efficiency; however, they are generally only applicable when vessel speeds are low and the lateral separation distance between ships is sufficiently large.
Recent advances in computational fluid dynamics (CFD) have expanded the use of numerical methods aimed at accurately predicting wave-making effects and hydrodynamic interactions induced by passing ships (Huang and Chen, 2007; Kok et al., 2018; Pawar et al., 2018; Nandhini & Nallayarasu, 2020; Zhou et al., 2021; Denehy, 2022). Although CFD simulations require substantial computational resources, they offer the significant advantage of accurately predicting ship motions and mooring characteristics under a wide range of environmental and operational conditions. Some previous studies, such as that of Nikushchenko and Zubova (2015), performed numerical simulations under a quasi-steady assumption by varying the distance between vessels. However, such simplifications inherently limit prediction accuracy. While several studies have incorporated unsteady effects, further improvements are still needed to accurately predict ship interactions in confined waterways and under extreme operating conditions (Huang & Chen, 2007; Pawar et al., 2018; Nandhini and Nallayarasu, 2020; Zhou et al., 2021). Recognizing these challenges, the 6th MASHCON conference emphasized that validation studies based on benchmark tests are essential for improving the accuracy and reliability of numerical predictions (Zwijnsvoorde et al., 2022; Kwon & Yeon, 2023; Yu et al., 2022; Zheng et al., 2022).
This study aims to evaluate the hydrodynamic loads acting on a moored ship due to the passage of a vessel in confined waters and to systematically investigate the effects of key parameters, including vessel speed, separation distance, water depth, and quay wall clearance. To achieve this, a benchmark case presented at the 6th MASHCON conference was adopted to validate the numerical methodology. Realistic passing-ship scenarios were then simulated using CFD based on the Unsteady Reynolds-Averaged Navier–Stokes (URANS) equations coupled with an overset mesh technique. By quantitatively evaluating the hydrodynamic forces and moments acting on the moored ship, as well as variations in the free surface, this study extended previous investigations by considering practical design parameters, such as quay wall clearance, in addition to the variables commonly examined in earlier research. As the sinkage and trim motions of both the passing and moored ships were found to be negligible in the benchmark model tests, all degrees of freedom except for the forward motion of the passing vessel were constrained in the present study. This simplification improved the computational efficiency and numerical stability of the simulations while allowing the analysis to focus on the quantitative effects of various design parameters. Therefore, the results of this study are expected to serve as fundamental reference data for the development of practical design and operational guidelines to ensure the safety of working vessels in port environments and the safe navigation of passing ships.

2. Problem Descriptions

To validate the numerical methodology, a benchmark test provided at the 6th MASHCON conference was selected, and the numerical results were compared against the corresponding experimental data (Zwijnsvoorde et al., 2022). The MASHCON benchmark test serves as a reliable reference for validating numerical simulations and was specifically designed to assess the capability of numerical models to accurately capture complex hydrodynamic interactions between passing and moored vessels. Among the available benchmark cases, C0406S01_CI3900 was selected as a representative case. The passing ship was modeled as a KRISO Container Ship (KCS; ID: C04), while the moored ship was modeled as a Neo-Panamax container ship (ID: C0P). The hull geometries and key specifications of both vessels are presented in Fig. 1 and Table 1. No appendages were included in either ship model, and the blue line indicates the calm-water surface. The benchmark test conditions are summarized in Table 2, and the layout of the towing tank and ship arrangement is illustrated in Fig. 2. A tank wall was installed on the starboard side of the passing ship to represent a quay wall. The width of the towing tank was six times the beam of the passing ship (BC04), and the tank length was 71 m. The lateral separation distance between the passing and moored ships (dpas) was set to 1.92 times the beam of the passing ship (BC04), where dpas denotes the distance from the starboard side of the passing ship to the port side of the moored ship. The clearance between the starboard side of the moored ship and the quay wall was 20 mm. The water depth in the towing tank was defined based on the underkeel clearance of the passing ship. The underkeel clearance corresponded to 50% of the draft of the passing ship (TC04), resulting in a water depth of 0.285 m. The speed of the passing ship was set to 12 knots (6.17 m/s) at full scale, corresponding to 0.69 m/s at model scale. The ship-length-based Froude number (FrL) was 0.1, representing a low-speed regime in which wave-making effects are relatively weak. The depth-based Froude number (Frh) was 0.413, which is below the critical value of 0.7 commonly used to characterize shallow-water flow conditions. However, in confined waters, ship hydrodynamics are influenced not only by shallow-water effects caused by depth restrictions but also by blockage effects arising from the proximity to the quay wall. Therefore, in the present benchmark case, Kelvin wave generation was expected to remain relatively weak, whereas drawdown waves—influenced by both the seabed and side boundary—were expected to propagate slowly and significantly influence the nearby moored ship.
The passing ship was initialized from rest, accelerated to the target speed, and then maintained at a constant forward speed throughout the simulation, while the moored ship remained fixed near the quay wall. In the model experiments conducted by Zwijnsvoorde et al. (2022), only the heave and pitch degrees of freedom were allowed for both the passing and moored ships to measure ship sinkage and trim. However, because the measured sinkage and trim motions were negligible, the present study constrained all degrees of freedom besides the forward motion of the passing ship. Numerical simulations were then performed, and the surge force (X), sway force (Y), and yaw moment (N) acting on the moored ship were calculated for comparison with the experimental data (Kwon & Yeon, 2023). In addition, wave gauges were installed around the moored ship at the same locations used in the benchmark experiments to measure variations in free-surface elevation during the passage of the ship. The five wave gauges were designated as WG1–WG5, following the benchmark test configuration described by Zwijnsvoorde et al. (2022).

3. CFD Methods

3.1 Governing Equations and Numerical Methods

In this study, numerical simulations were performed using STAR-CCM+ Ver. 15.04, a commercial CFD software package based on the finite volume method. The flow field was assumed to be three-dimensional, unsteady, incompressible, and viscous. To solve the governing flow equations, the Unsteady Reynolds-Averaged Navier–Stokes (URANS) equations were employed. The corresponding continuity and momentum conservation equations are expressed by Eqs. (1) and (2), respectively:
(1)
∂(ρui¯)∂xi=0
(2)
∂(ρui¯)∂t+∂∂xj(ρui¯uj¯)=-∂p¯∂xi+∂∂xj[μ(∂ui¯∂xj+∂uj¯∂xi)]-∂∂xj(ρui′uj′¯)
Here, ρ and μ denote the fluid density and dynamic viscosity, respectively; ui¯ represents the time-averaged velocity component in the i-direction; p̄ denotes the time-averaged pressure; and ρui′uj′¯ represents the Reynolds stress tensor. To close the Reynolds stress term associated with turbulence, the SST k-ω turbulence model proposed by Menter (1993) was adopted. In addition, the Volume of Fluid method developed by Hirt and Nichols (1981) was employed to capture the free-surface interface. The High-Resolution Interface Capturing scheme, which provides second-order accuracy, was used to calculate the volume fraction at cell faces. For temporal discretization, a first-order implicit Euler scheme was applied, while the convection and diffusion terms were discretized using second-order upwind and second-order central differencing schemes, respectively. Pressure–velocity coupling was achieved through the Semi-Implicit Method for Pressure-Linked Equations algorithm. To efficiently represent the turbulent boundary layer near solid walls, wall functions were employed. Specifically, the All y+ Wall Treatment available in STAR-CCM+ was adopted. In this approach, the low-y+ wall treatment is applied as y+ approaches zero, while the high-y+ wall treatment is used when y+ xceeds 30. For the intermediate range of 1 < y+ < 30, a blending function is employed to smoothly transition between the two formulations. To simulate the motion of the passing ship, a dynamic overset mesh method was applied. The computational domain was divided into a background mesh region containing the moored ship and an overset mesh region surrounding the passing ship, with the overset mesh embedded within the background mesh. At the interpolation interface between the two mesh regions, flow variables were exchanged through linear interpolation, enabling the coupled solution of the flow field across the overlapping domains.

3.2 Computational Setup

Fig. 3 illustrates the computational domain and boundary conditions employed in the numerical towing-tank simulations. The width, water depth, and initial separation distance between the vessels were set to be identical to those of the MASHCON benchmark experiments. To provide sufficient distance for the acceleration of the passing ship and minimize wave reflections, the length of the computational domain was extended to 76 m. A velocity inlet boundary condition was imposed at the upstream boundary, while pressure outlet boundary conditions were applied at the top and starboard boundaries. No-slip wall boundary conditions were assigned to the ship hull surfaces, bottom boundary, and side walls. To suppress transient flow disturbances generated during the initial acceleration of the passing ship, a wave-damping technique was applied along the upstream, downstream, and side boundaries during the first 4 s of the simulation. The damping zone length was set to approximately 3.5 times the beam of the passing ship. The damping effect was gradually reduced with simulation time and completely removed after 4 s (Kwon & Yeon, 2023). For the CFD simulations, both an earth-fixed coordinate system—O-x0y0z0—and body-fixed coordinate system—O-xyz—were employed. In the earth-fixed coordinate system (x0, y0, z0), the x0-axis was aligned with the ship’s direction of motion, while the z0-axis was oriented opposite to the direction of gravity. In the body-fixed coordinate system (x, y, z), the x-axis was aligned with the ship’s longitudinal direction, whereas the z-axis was defined in the direction of gravity. The x0y0-plane of the earth-fixed coordinate system corresponds to the calm-water surface. In contrast, the origin of the body-fixed coordinate system was located at the intersection of the midship section, centerline, and calm-water surface of each vessel and moved together with the corresponding ship.
The forces and moments acting on the moored ship due to its continuous interaction with the passing ship were calculated in the body-fixed coordinate system (x, y, z) of the moored ship. To describe the instantaneous hydrodynamic loads, the relative position between the two vessels was considered. The longitudinal position of the passing ship relative to the moored ship was normalized by the mean ship length, , and is expressed as Eq. (3) (Zwijnsvoorde et al., 2022).
(3)
ξ=2(xp-xm)/(Lpp,p+Lpp,m)
Here, the subscripts p and m denote the passing and moored ships, respectively. The variable x denotes the longitudinal position of the body-fixed coordinate system in the earth-fixed frame, and Lpp denotes the length between perpendiculars of the ship. The time step (Δt) was selected to satisfy the criterion proposed by ITTC (2014) — Δt ≤ 0.01Lpp,p/Vp — and a time interval of 0.02 s was used for all simulations.
Fig. 4 presents the mesh distribution around the moored and passing ships, as well as the free surface. The computational mesh was generated using the automated meshing tools available in STAR-CCM+, employing a trimmed mesh for the bulk flow region and prism-layer meshes near solid boundaries. On the hull surfaces of both the passing and moored ships, the y+ value was maintained below 10 to ensure an adequate resolution of the near-wall flow. To improve the accuracy of the flow simulation, locally refined meshes were applied in regions where complex flow phenomena were expected, including the free surface, vicinity of the ship hulls and seabed, interaction zone where the passing ship travels close to the moored ship, trajectory of the passing ship, and a narrow gap between the moored ship and quay wall. When the overset mesh technique is employed, interpolation of flow variables is performed within the interface region where the overset mesh overlaps with the background mesh as the ship moves. This interpolation process may introduce numerical errors. To minimize such interpolation errors, the mesh sizes of the overset and background mesh blocks were designed to be as similar as possible in the vicinity of the overset interface.

3.3 Mesh Convergence Study and Validation

Prior to comparison with the benchmark test data, a grid convergence study was conducted to assess the numerical accuracy of the simulations. Three mesh systems were generated: coarse, medium, and fine grids. The total numbers of cells for each mesh are summarized in Table 3. All simulations were performed using a fixed time step of 0.02 s. To quantitatively evaluate grid sensitivity, the grid convergence assessment procedure established by Celik et al. (2008), based on the Grid Convergence Index (GCI) concept originally proposed by Roache (1994), was adopted. This method provides a reliable framework for quantitatively assessing grid independence. In the present study, the convergence characteristics of each mesh configuration were analyzed using Eqs. (4)–(10).
(4)
R=ɛ21ɛ32
(5)
p=1ln(r21)|ln|ɛ32ɛ21|+q(p)|
(6)
q(p)=ln(r21p-sr32p-s)
(7)
s=1•sgn(ɛ32ɛ21)
(8)
Qext21=r21pQ1-Q2r21p-1
(9)
ea21=|Q1-Q2Q1|
(10)
GCIfine21=1.25r21p-1|Q1-Q2Q1|
Here, the subscripts 1, 2, and 3 denote the fine, medium, and coarse grids, respectively. The convergence characteristics of the grid system were evaluated using the convergence ratio, R=ɛ21/ɛ32, defined in Eq. (4). A value of 0 < R < 1 indicates monotonic convergence, whereas − 1 < R < 0 indicates oscillatory convergence. In the expression ɛij = Qi − Qj, which represents the difference in the physical quantity between two grid levels, Qi denotes the value computed on the i-th grid. The grid refinement ratio r21 represents the grid-size ratio between the fine and medium grids and was determined according to the procedure proposed by Celik et al. (2008) for unstructured three-dimensional meshes. In the present study, the average global grid refinement ratio for each mesh set was maintained at approximately 1.19. For unstructured meshes, when the grid refinement ratios between the fine–medium and medium–coarse grids were not identical, the apparent order of accuracy (p) was determined using Eqs. (5)–(7). In particular, the parameter s in Eq. (7) denotes the sign function, and a negative value indicates oscillatory convergence behavior. Eqs. (8) and (9) represent the extrapolated value and approximate relative error, respectively, calculated based on the fine and medium grid solutions. Based on these quantities, the GCI for the fine grid is calculated using Eq. (10). The factor 1.25 corresponds to the safety factor (FS) recommended by Celik et al. (2008) for convergence studies employing three levels of grid refinement (Islam & Soares, 2021).
Fig. 5 presents the surge force (X), sway force (Y), and yaw moment (N) acting on the moored ship during the passage of the passing ship as functions of the relative position between the centers of the moored and passing ships, as defined in Eq. (3). As shown in Fig. 5, the locations at which the peak values of the hydrodynamic forces and moments (X, Y, and N) occur agree well with the model test results. The convergence assessment was performed at the locations corresponding to the maximum peak value of each force or moment, as indicated by red circles in Fig. 5. The results of the grid convergence study are summarized in Table 4. The GCI-based uncertainties for the fine grid were estimated to be 0.85%, 0.02%, and 3.06% for X, Y, and N, respectively. In addition, the relative errors between the fine-grid simulation results and model test data, calculated as D% = 100 × (S − E)/E, were −2.44%, −2.85%, and −7.19% for X, Y, and N, respectively. As the mesh was refined from coarse to fine, the numerical results generally exhibited convergence towards the experimental measurements. Considering both the GCI values obtained for the fine grid and differences between the numerical and experimental results, the fine-grid system was selected as the reference mesh for all subsequent simulations in this study.

3.4 Major Influencing Parameters

The speed of the passing ship, separation distance between the passing and moored ships, water depth, and gap between the quay wall and moored ship were selected as the principal parameters affecting passing-ship interactions. To express these parameters in nondimensional form, the speed of the passing ship was represented by the depth-based Froude number Frh=Vp/gh. The water depth was normalized by the draft of the passing ship and defined as h/T=h/TC04. The separation distance was expressed as SR=dpas/BC04, representing the ratio of the lateral separation distance to the beam of the passing ship. Similarly, the gap between the quay wall and the moored ship was defined as GR=dquay/BC04, corresponding to the ratio of the quay wall gap to the beam of the passing ship. The ranges of all parameters were determined based on values investigated in previous studies and are summarized in Table 5.
The numerical simulations were conducted by varying only one parameter at a time while keeping all other parameters constant. For the parametric study, the bold values in Table 5 correspond to the C0406S01_CI3900 case from the MASHCON benchmark tests. To quantitatively compare the effects of parameter variations on the moored ship, the surge force (X)), sway force (Y), and yaw moment (N) acting on the moored ship were reformulated as nondimensional coefficients, denoted by CX, CY, and CM, respectively. These nondimensional coefficients are defined as follows:
(11)
CX=X12ρU2A,CY=Y12ρU2A,CM=N12ρU2AL
Here, ρ is the fluid density, U is the speed of the passing ship, A is the lateral wetted area of the moored ship, and L is the reference length, which corresponds to Lpp in the present study.
To quantify the relationships between the governing parameters and peak hydrodynamic loads, curve-fitting analyses were performed. A power-law regression model of the form y = axb was adopted for the analysis. The goodness-of-fit of each regression model was evaluated using the coefficient of determination (R2), where values closer to 1 indicate a higher degree of predictive accuracy.

4. Results And Discussions

In this section, the hydrodynamic response characteristics of the moored ship under varying passing-ship conditions are compared and analyzed using the nondimensional coefficients (CX, CY, and CM) defined earlier. These coefficients are formulated according to Eq. (11), and all subsequent comparisons of load magnitudes and trends are primarily based on the nondimensional coefficients. For ease of physical interpretation, however, the corresponding dimensional quantities, namely the surge force (X), sway force (Y), and yaw moment (N), are also presented where appropriate.

4.1 Passing Ship Effects on Moored Ship

To investigate the mechanisms responsible for the hydrodynamic loads acting on a moored ship during the passage of a vessel, the numerical results of the MASHCON benchmark case were analyzed. Fig. 6 presents the variations in the nondimensional surge force (CX, sway force (CY), and yaw moment (CM) acting on the moored ship as functions of the relative position between the two vessels (ξ). The figure also shows the free-surface elevation (η/h) measured at the wave gauges (WG1–WG5) located around the moored ship. When ξ is between approximately −5 and −2, a solitary wave or bow wave, generated by the bow of the passing ship, propagates past the moored ship. The generated wave travels from the stern (WG1) towards the bow (WG5) of the moored ship, inducing a relatively small negative CX. Subsequently, a low-pressure region associated with the drawdown wave begins to directly influence the moored ship. The drawdown wave is characterized by a reduction in free-surface elevation and an increase in flow velocity caused by shallow-water effects. At approximately ξ = −0.4, the free-surface elevation at the stern (WG1) decreases sharply due to the drawdown wave, whereas the bow region (WG5) remains under the influence of the bow wave and still exhibits an elevated water level. Consequently, the difference in free-surface elevation between the bow and stern reaches its maximum, causing CX to reach its maximum negative value, corresponding to the location where the dimensional surge force (X) reaches its peak magnitude. As the passing ship approaches ξ ≈ 0, the centers of the two vessels become laterally aligned, intensifying the suction flow associated with the drawdown wave. Consequently, the moored ship experiences a strong suction effect towards the passing ship. As a result, CY reaches its maximum negative value, corresponding to the peak sway force (Y). At approximately ξ ≈ 0.5, the free-surface elevation near the bow of the moored ship (WG5) decreases rapidly owing to the drawdown wave, while the water level near the stern becomes relatively higher. This reversal of the free-surface elevation difference between the bow and stern causes CX to reach its maximum positive value. Therefore, throughout the entire passing process, the nondimensional surge force (CX), sway force (CY), and yaw moment (CM) exhibit strongly nonlinear behavior as functions of the relative position ξ.
Figs. 7–9 visually illustrate the hydrodynamic interactions between the passing and moored ships at relative positions (ξ) of −0.4, 0, and +0.4, respectively. In each figure, the first and second panels present plan views of the free-surface elevation and pressure distributions, respectively, while the third panel shows the pressure distribution acting on the moored ship, displayed sequentially for the starboard side, bottom surface, and port side. Fig. 7 corresponds to the instance when the midship section of the passing ship reaches the stern region of the moored ship. At this position, the drawdown wave generated near the midship region of the passing ship causes a reduction in free-surface elevation and the formation of a low-pressure region, which is concentrated around the stern of the moored ship. Consequently, the pressure acting on the stern becomes lower than that acting on the bow, inducing a flow field directed towards the stern. As a result, a negative surge force (X) acts predominantly on the moored ship. Fig. 8 represents the condition in which the passing and moored ships are almost side-by-side. At this stage, the low-pressure region generated around the midship section of the passing ship extends over most of the moored ship, producing a strong suction effect towards the passing ship. Consequently, the sway force (Y) acting on the moored ship reaches its maximum magnitude. Fig. 9 shows the moment when the midship section of the passing ship reaches the bow region of the moored ship. In this case, the low-pressure region develops primarily around the bow of the moored ship. Therefore, the moored ship experiences a flow field that tends to push it forward, leading to the dominance of a positive surge force (X). Taken together, the results presented in Figs. 6–9 clearly demonstrate the influence of the solitary and drawdown waves generated by the passing ship on the moored ship under confined-water and shallow-water conditions.

4.2 Influencing of Passing Ship Speed

Fig. 10 presents the variations in free-surface elevations measured at WG1, WG3, and WG5 as functions of the passing ship’s travel distance for six different ship-speed conditions. The passing ship speed ranged from 6 to 16 kn (3.09–8.23 m/s) at full scale, corresponding to depth-based Froude numbers (Frh) of 0.206–0.55 and ship-length-based Froude numbers (FrL) of 0.053–0.14. The simulations were conducted under the conditions of h/T = 1.5, SR = 3.92, and GR = 0.0327. As the passing ship speed increases, the amplitude of the bow wave becomes larger, and the free-surface depression induced by the drawdown wave becomes more pronounced. In particular, when the ship speed increases from 8 kn (4.12 m/s) to 16 kn (8.23 m/s), the maximum bow-wave height at WG3 increases by a factor of 4.3, while the maximum free-surface depression caused by the drawdown wave increases by a factor of 9.2. These results indicate that, in shallow and confined waters, the influence of the drawdown wave on a moored ship becomes increasingly significant relative to that of the bow wave as the passing ship speed increases. Furthermore, because bow waves propagate at a speed determined primarily by the water depth under shallow-water conditions, the distance between the arrival of the bow and drawdown waves at a given wave-gauge location decreases as the passing ship speed increases. Consequently, the two wave systems tend to merge and behave like a single wave characterized by a shorter period and larger amplitude.
Fig. 11 presents the nondimensional hydrodynamic forces and moments (CX, CY, and CM) acting on the moored ship under different passing-ship speeds. As the passing ship speed increases, the higher-amplitude bow and drawdown waves described previously reach the moored ship in rapid succession. Consequently, the nondimensional hydrodynamic forces and moments acting on the moored ship exhibit increasingly unsteady and fluctuating behavior. These results indicate that the hydrodynamic loads acting on a moored ship are highly sensitive to the speed of the passing ship. The peak values of the nondimensional forces and moments extracted from Fig. 11 are plotted against the depth-based Froude number in Fig. 12, where curve fitting was performed to quantify the relationships between the variables. The relationships were represented using power-law regression equations of the form y = axb. All coefficients increased with increasing passing-ship speed; however, the exponent values were less than unity (b < 1), indicating a sublinear growth trend. In particular, CX and CM exhibited strong correlations with the passing-ship speed, with R2 values greater than 0.9, suggesting a high sensitivity to speed variations. In contrast, CY showed a lower correlation (R2 = 0.69), indicating greater scatter in the data and a less distinct trend. Fig. 13 presents the free-surface elevation and pressure distributions around the moored ship at ξ = 0 for three different passing-ship speed conditions. As the passing-ship speed increases, the free-surface depression and pressure reduction become increasingly pronounced. The wave field generated under the present conditions is dominated by the primary wave system, and the structure of the Kelvin wave system becomes more distinct as the passing-ship speed increases. Nevertheless, its influence on the moored ship remains relatively limited compared with that of the drawdown wave.

4.3 Influencing of Water Depth

Fig. 14 presents the variations in free-surface elevation measured at WG1, WG3, and WG5 for different water-depth-to-draft ratios (h/T). The simulations were conducted under the conditions of Frh = 0.413, SR = 3.92, and GR = 0.0327, with h/T varying from 1.1 to 10. As the water depth decreases, the amplitude of the bow wave increases, and the free-surface depression induced by the drawdown wave becomes increasingly pronounced. For example, when h/T decreases from 2.0 to 1.1, the bow-wave amplitude at WG3 increases by approximately 2.6 times, while the maximum free-surface depression caused by the drawdown wave increases by approximately 3.4 times. Compared with the response observed under varying passing-ship speeds, these results indicate a relatively lower sensitivity to changes in water depth.
Fig. 15 presents the nondimensional hydrodynamic forces and moments acting on the moored ship for different water-depth-to-draft ratios (h/T). The results indicate that water depth has a greater influence on CY than on CX. Specifically, when h/T decreases from 2.0 to 1.1, the maximum value of CX increases by approximately three times, whereas the maximum value of CY increases by approximately 5.6 times. In contrast, for h/T ≥ 4, the influence of the passing ship on the moored ship becomes negligible, and the resulting hydrodynamic loads are correspondingly small. Fig. 16 illustrates the relationships between the peak hydrodynamic load coefficients and h/T. All fitted coefficients exhibit negative exponents (b < 0), indicating an inverse relationship with h/T. In particular, the hydrodynamic loads increase rapidly when h/T ≤ 2, demonstrating that the influence of the passing ship is significantly amplified under shallow-water conditions due to strong bottom effects. The regression analysis further shows that CY is the most sensitive parameter to changes in water depth, with the largest exponent magnitude (|b|=3.69). Moreover, all regression models yielded R2 values greater than 0.98, indicating excellent agreement between the fitted curves and simulation results.
Fig. 17 presents the free-surface elevation and pressure distributions around the moored ship at =0 for three different h/T conditions. As the water depth decreases, the bottom effect becomes increasingly significant, leading to more pronounced free-surface depression and pressure reduction associated with the drawdown wave. Consequently, the pressure deficit acting on the moored ship becomes more evident. In contrast, when h/T = 4, the hydrodynamic influence of the passing ship is barely transmitted to the moored ship, indicating that interaction effects become negligible under relatively deep-water conditions.

4.4 Influencing of Separation Distance

Fig. 18 presents the free-surface elevations measured at wave gauges WG1, WG3, and WG5 for five different separation distance ratios (SR). The numerical simulations were conducted under the conditions of Frh = 0.413, h/T = 1.5, and GR = 0.0327, with SR values of 1.42, 2.25, 3.09, 3.92, and 4.75. The results indicate that the primary wave system dominates the hydrodynamic response under the present conditions, and the free-surface depression associated with the primary wave becomes increasingly pronounced as the separation distance decreases. For example, when SR decreases from 4.75 to 1.42, corresponding to a reduction by a factor of approximately 3.3, the maximum free-surface depression at WG3 increases by approximately 2.6 times.
Fig. 19 shows the nondimensional hydrodynamic forces and moments acting on the moored ship for different separation distance ratios. As the separation distance decreases, the magnitudes of the hydrodynamic forces and moments acting on the moored ship increase substantially. The peak values of the nondimensional forces and moments are plotted against the separation distance ratio in Fig. 20. The regression analysis shows that all fitted coefficients have negative exponents (b < 0), indicating an inverse relationship between the hydrodynamic loads and separation distance ratio. In other words, the hydrodynamic loads acting on the moored ship decrease as the separation distance increases. Among the three load coefficients, CM exhibits the largest absolute exponent value, indicating that it is the most sensitive to variations in SR. Furthermore, all regression models yield R2 values greater than 0.98, demonstrating excellent correlation and confirming the reliability of the fitted relationships. These results quantitatively demonstrate that hydrodynamic interactions become significantly stronger as the separation distance decreases and provide an important basis for establishing minimum clearance requirements in practical design and operation. Fig. 21 presents the free-surface elevation and pressure distributions around the moored ship at ξ = 0 for three different separation distance conditions. As shown in the figure, both the free-surface depression and pressure reduction in the gap between the passing and moored ships become increasingly pronounced as the separation distance decreases. Conversely, as the separation distance increases, the interaction between the port side of the passing ship and the region opposite the quay wall becomes more notable, resulting in a slight increase in free-surface depression and pressure reduction in that area.

4.5 Influence of Gap Between Moored Ship and Quay Wall

When a ship is berthed and moored alongside a quay wall, fenders are required to protect both the vessel and the quay structure from impact loads. With the recent trend towards larger vessels, the reinforcement of aging quay walls and the construction of new berthing facilities have become increasingly common worldwide. In the MASHCON benchmark case adopted in this study, the moored ship was also modeled as a large vessel, and the ratio of the gap between the moored ship and quay wall to the ship beam (GR) was set to 0.0327, corresponding to approximately 1.6 m at full scale. Numerical simulations were performed by varying the gap between the moored ship and quay wall from 1.6 to 9.6 m at full scale under the conditions of Frh = 0.413, h/T = 1.5, and SR = 3.92. The gap distance was defined based on the position of the moored ship. Consequently, variations in the gap between the moored ship and quay wall also resulted in corresponding changes in the separation distance between the passing and moored ships.
Fig. 22 presents the variations in free-surface elevation measured at wave gauges WG1, WG3, and WG5 located between the moored ship and quay wall for four different values of GR. Fig. 23 shows the corresponding nondimensional hydrodynamic forces and moments acting on the moored ship. As shown in the figures, all coefficients are only weakly affected by variations in GR. The coefficient CX, which is primarily governed by the pressure difference between the bow and stern, tends to decrease slightly as GR increases; however, the magnitude of this change remains relatively small. In contrast, CY, which is influenced by the pressure difference between the port and starboard sides of the ship, exhibits an increasing trend with increasing GR. As a result, CM also increases accordingly. These tendencies can be further observed in Fig. 24 and are considered to be associated with changes in blockage effects under the given water depth and wavelength conditions. As GR increases from 0.0327 to 0.1963, corresponding to a sixfold increase in the gap distance, CX decreases slightly, whereas CY increases. This indicates that, compared with the other governing parameters examined in this study, the influence of GR on the hydrodynamic loads acting on the moored ship is relatively limited.
Fig. 25 presents the wave patterns and pressure distributions around the moored ship at a relative position of zero for two different GR conditions. Because the operating conditions of the passing ship remain unchanged, the propagation characteristics of the bow wave and primary wave system are generally similar in both cases. However, when GR increases to 0.1963, the pressures on both the port and starboard sides of the moored ship become lower than those observed under smaller GR conditions. This behavior can be attributed to the reduction of the blockage effect caused by the quay wall, which allows the port side of the moored ship to be more exposed to the primary wave system and consequently reduces the pressure difference between the port and starboard sides. Consequently, the sway force (Y) and yaw moment (N) increase with increasing GR. Nevertheless, the overall level of hydrodynamic loading remains relatively insensitive to changes in GR.

5. Conclusions

This study employed a CFD approach to investigate the hydrodynamic loads acting on a moored ship due to passing-ship effects under various operating conditions of large vessels. Numerical simulations were conducted to quantitatively analyze passing-ship interactions in confined waters using STAR-CCM+, a commercial CFD solver based on the URANS equations, with reference to the MASHCON 2022 benchmark case. A grid convergence study was performed for the C0406S01_CI3900 benchmark case, in which a KCS passed a moored ship using a dynamic overset mesh technique. The results demonstrated the reliability of the numerical model.
The hydrodynamic loads acting on the moored ship were compared with experimental measurements, and the validity of the numerical model was assessed based on both grid convergence and the discrepancy between the numerical and experimental results. The validated model was subsequently applied to a range of operating conditions in confined waters, demonstrating its capability to reliably reproduce passing-ship interaction phenomena. The simulation results identified the principal parameters governing passing-ship effects as the passing-ship speed, separation distance between vessels, water depth, and gap ratio between the moored ship and quay wall. The main findings are summarized as follows:
  • (1) As the passing-ship speed increased, the free-surface depression and pressure reduction induced by the drawdown wave became more pronounced, and the influence of the primary wave system on the moored ship also increased. Although the effects of the Kelvin wave system became more evident at higher speeds, their overall contribution remained relatively limited.

  • (2) As the water depth decreased, the free-surface depression and pressure reduction associated with the drawdown wave became increasingly significant. In contrast, when the water-depth-to-draft ratio exceeded 4, the influence of the passing ship on the moored ship became negligible, and the resulting hydrodynamic loads were correspondingly small.

  • (3) As the separation distance ratio decreased, the hydrodynamic interaction between the passing and moored ships intensified, leading to increased hydrodynamic loads. Conversely, increasing the separation distance reduced the loads acting on the moored ship; however, interactions with the region opposite the quay wall became more notable, highlighting the importance of selecting an appropriate separation distance.

  • (4) As the gap ratio between the moored ship and quay wall (GR) increased, the blockage effect was alleviated, and the suction effect tended to increase. However, considering the use of fenders in actual port environments, the influence of GR may be relatively limited.

Power-law regression analyses were performed using the peak nondimensional force and moment coefficients (CX, CY, and CM) acting on the moored ship for each governing parameter. The results indicate that the sensitivity of the hydrodynamic loads varies depending on the passing-ship speed, water depth, separation distance, and gap ratio between the moored ship and quay wall. No single coefficient was dominant under all conditions; instead, the primary influencing factor varied according to the operating conditions considered. These findings are consistent with those reported in previous studies, supporting the validity of the present analysis. The present study demonstrates the reliability of a numerical model for predicting passing-ship interactions in confined waters. The validated model is expected to contribute to the development of practical design and operational guidelines for ensuring the safety of working vessels in port environments and establishing safe navigation routes for vessels entering and leaving ports.

Conflict of Interest

Dongho Jung serves as a journal publication committee member of the Journal of Ocean Engineering and Technology. However, he was not involved in the decision to publish this article. The authors have no potential conflict of interest relevant to this article.

Funding

This research was supported by Korea Institute of Marine Science & Technology Promotion (KIMST) funded by the Ministry of Oceans and Fisheries (RS-2023-00236321/PMS6750).

Fig. 1
Model ship geometries
ksoe-2025-031f1.jpg
Fig. 2
Schematic of the selected benchmark test case
ksoe-2025-031f2.jpg
Fig. 3
Computational domain and boundary conditions
ksoe-2025-031f3.jpg
Fig. 4
Mesh distributions in background and overset regions
ksoe-2025-031f4.jpg
Fig. 5
Forces and moments acting on the moored ship for different grid sizes
ksoe-2025-031f5.jpg
Fig. 6
Nondimensional force and moment coefficients acting on the moored ship and nondimensional wave elevation near the moored ship
ksoe-2025-031f6.jpg
Fig. 7
Simulation results at ξ = −0.4
ksoe-2025-031f7.jpg
Fig. 8
Simulation results at ξ = 0.0
ksoe-2025-031f8.jpg
Fig. 9
Simulation results at ξ = 0.4
ksoe-2025-031f9.jpg
Fig. 10
Non-dimensional wave elevation for the passing ship speed effects
ksoe-2025-031f10.jpg
Fig. 11
Nondimensional force and moment coefficients acting on the moored ship for the passing ship speed effects
ksoe-2025-031f11.jpg
Fig. 12
Variation of peak force and moment coefficients with depth-Froude number (Frh)
ksoe-2025-031f12.jpg
Fig. 13
Simulation results at ξ = 0.0 of the different depth-Froude number (Frh)
ksoe-2025-031f13.jpg
Fig. 14
Nondimensional wave elevation for the water depth effects
ksoe-2025-031f14.jpg
Fig. 15
Nondimensional forces and moment coefficients acting on the moored ship for different water-depth-to-draft ratios (h/T)
ksoe-2025-031f15.jpg
Fig. 16
Variation of peak force and moment coefficients with water-depth-to-draft ratio (h/T)
ksoe-2025-031f16.jpg
Fig. 17
Simulation results at ξ = 0.0 of the different water-depth-to-draft ratios (h/T)
ksoe-2025-031f17.jpg
Fig. 18
Nondimensional wave elevation for the separation distance effects
ksoe-2025-031f18.jpg
Fig. 19
Nondimensional force and moment coefficients acting on the moored ship for the separation distance effects
ksoe-2025-031f19.jpg
Fig. 20
Variation of peak force and moment coefficients with separation ratio (SR)
ksoe-2025-031f20.jpg
Fig. 21
Simulation results at ξ = 0.0 of the different separation ratios (SR)
ksoe-2025-031f21.jpg
Fig. 22
Nondimensional wave elevation for the quay wall gap effects
ksoe-2025-031f22.jpg
Fig. 23
Nondimensional force and moment coefficients acting on the moored ship for the quay wall gap effects
ksoe-2025-031f23.jpg
Fig. 24
Variation of peak force and moment coefficients with quay wall gap ratio (GR)
ksoe-2025-031f24.jpg
Fig. 25
Simulation results at ξ = 0.0 of quay wall gap ratio (GR)
ksoe-2025-031f25.jpg
Table 1
Main particulars of the two model ships
Particulars Symbol KCS Neo-Panamax
Scale ratio (-) λ 1/80 1/80
ID (-) - C04 C0P
Length between perpendiculars (m) Lpp 4.367 4.350
Breadth (m) B 0.611 0.610
Draft (m) T 0.190 0.190
Table 2
Benchmark test conditions for the selected case
Particulars Symbol Model Full
Length of the tank (m) L 71.0 5,680
Width of the tank (m) W 6.11 488.8
Depth of the tank (m) h 0.285 22.8
Under keel clearance (m) UKC 0.095 7.6
Passing distance (m) dpas 2.396 191.7
Passing speed (m/s) Vpas 0.690 6.173
Froude number (-) FrL 0.105 0.105
Depth-based Froude number (-) Frh 0.413 0.413
Table 3
Cell numbers for each mesh set
Mesh set Total number of cells
Coarse 2,594,036
Medium 4,462,490
Fine 7,570,774
Table 4
Grid convergence study results
Item X (N) Y (N) N (N·m)
Q1 −2.817 −1.211 −0.601
Q2 −2.760 −1.208 −0.587
Q3 −2.597 −1.247 −0.556
R 0.287 −0.07 0.481
p 7.036 14.759 3.952
Qext21 −2.826 −1.211 −0.616
ea21 1.66% 0.22% 2.46%
GCIfine21 0.85% 0.02% 3.06%
Table 5
Simulation conditions for the parametric study
Item Frh h/T SR GR
Ship speed 0.140 1.5 3.92 0.0327
0.123 1.5 3.92 0.0327
0.105 1.5 3.92 0.0327
0.088 1.5 3.92 0.0327
0.070 1.5 3.92 0.0327
0.053 1.5 3.92 0.0327
Water depth 0.105 1.1 3.92 0.0327
0.105 1.3 3.92 0.0327
0.105 1.5 3.92 0.0327
0.105 2.0 3.92 0.0327
0.105 4.0 3.92 0.0327
0.105 10.0 3.92 0.0327
Passing distance 0.105 1.5 1.42 0.0327
0.105 1.5 2.25 0.0327
0.105 1.5 3.09 0.0327
0.105 1.5 3.92 0.0327
0.105 1.5 4.75 0.0327
Quay wall distance 0.105 1.5 3.92 0.0327
0.105 1.5 3.92 0.0654
0.105 1.5 3.92 0.0982
0.105 1.5 3.92 0.1963

References

Böttner, C. U., & Kondziella, B. (2022). Passing ship effect in shallow and confined waters, a systematic model test study of moored containership at quay. Proceedings of the 6th MASHCON Glasgow, UK: 10-18.

Celik, I. B., Ghia, U., Roache, P. J., Freitas, C. J., Coleman, H., & Raad, P. E. (2008). Procedure for estimation and reporting of uncertainty due to discretization in CFD applications. Journal of fluids Engineering-Transactions of the ASME, 130(7), 078001. https://doi.org/10.1115/1.2960953
crossref
Denehy, S. P. (2022). Modelling of Berthed Ship-Passing Ship Interaction Forces and Moments in Shallow and Confined Water. Doctoral dissertation. University of Tasmania.

Hirt, C. W., & Nichols, B. D. (1981). Volume of fluid (VOF) method for the dynamics of free boundaries. Journal of Computational Physics, 39(1), 201-225. https://doi.org/10.1016/0021-9991(81)90145-5
crossref
Huang, E. T., & Chen, H. C. (2007). Influences of site specifics on passing ship effects. ISOPE International Offshore and Polar Engineering Conference, 2556-2563.

International Gas Union (IGU). (2025). 2025 World LNG Report. https://www.igu.org/igu-reports/2025-world-lng-report

Islam, H., & Soares, C. G. (2021). Assessment of uncertainty in the CFD simulation of the wave-induced loads on a vertical cylinder. Marine Structures, 80, 103088. https://doi.org/10.1016/j.marstruc.2021.103088
crossref
International Towing Tank Conference (ITTC). (2014). Practical guidelines for ship CFD applications. ITTC Recommended Procedures and Guidelines (7.5-03-02-03, Revision 01).

Jung, S. J., Oh, S. H., Jung, D. W., Kim, Y. H., & Jung, D. H. (2020). Experimental and Numerical Study of Berthing and Unberthing of LNG-Bunkering Vessels. Journal of Navigation and Port Research, 44(6), 439-446.

Jung, S. J., Jung, D. W., Oh, S. H., Kim, Y. H., & Jung, D. H. (2021). Numerical Assessment of LNGC Berthing Operation to FLBT. Journal of Navigation and Port Research, 45(3), 87-94.

Kok, Z., Jin, Y., Chai, S., Denehy, S., & Duffy, J. (2018). URANS prediction of berthed ship–passing ship interactions. Ships and Offshore Structures, 13(6), 561-574. https://doi.org/10.1080/17445302.2018.1429136
crossref
Kriebel, D. (2007). Mooring loads due to parallel passing ships. Proceedings of Ports 2007, 30 Years of Sharing Ideas: 1977–2007 1-10. https://doi.org/10.1061/40834(238)46
crossref
Kwon, C. S., & Yeon, S. M. (2023). CFD study to predict the effect of a passing ship on moored ships in a confined waterway. International Journal of Naval Architecture and Ocean Engineering, 15, 100527. https://doi.org/10.1016/j.ijnaoe.2023.100527
crossref
Lataire, E., Vantorre, M., & Delefortrie, G. (2009). Captive model testing for ship to ship operations. In International Conference on Marine Simulation and Ship Maneuverability (MARSIM'09) Panama Canal Authority; International Marine Simulator Forum.

Lataire, E., Vantorre, M., Vandenbroucke, J., & Eloot, K. (2011). Ship to ship interaction forces during lightering operations. Proceedings of the 2nd International Conference on Ship Manoeuvring in Shallow and Confined Water: Ship to Ship Interaction, 211-221.

Lee, J.-S., & Jung, S.-W. (2022). 국내 최초의 LNG 벙커링 선박 K LNG Dream 호 . Korea’s first LNG bunkering ship: K LNG Dream Bulletin of the Society of Naval Architects of Korea, 59(6), 64-67.

Menter, F. R. (1993). Zonal two equation k-w turbulence models for aerodynamic flows. Proceedings of the 24th Fluid Dynamics Conference (AIAA-93-2906) https://doi.org/10.2514/6.1993-2906
crossref
Nandhini, V., & Nallayarasu, S. (2020). CFD simulation of the passing vessel effects on moored vessel. Ships and Offshore Structures, 15(2), 184-199. https://doi.org/10.1080/17445302.2019.1606764
crossref
Nikushchenko, D. V., & Zubova, A. A. (2015). Hydrodynamic interaction forces and moments prediction methodology for the ship behavior prediction during the overtaking maneuver. SNAME Maritime Convention and 5th World Maritime Technology Conference (D021S005R007). https://doi.org/10.5957/WMTC-2015-287
crossref
Park, J. Y., Nam, B. W., & Kim, Y. (2021). Numerical analysis of hydrodynamic loads on passing and moored ships in shallow water. Processes, 9(3), 558. https://doi.org/10.3390/pr9030558
crossref
Pawar, R., Bhar, A., & Dhavalikar, S. S. (2018). Numerical prediction of hydrodynamic forces on a moored ship due to a passing ship. Proceedings of the Institution of Mechanical Engineers, Part M: Journal of Engineering for the Maritime Environment, 233(2), 575-585. https://doi.org/10.1177/1475090218770039
crossref
Pinkster, J. A. (2009). Suction, seiche and wash effects of passing ships in ports. SNAME Maritime Convention (D011S001R008). https://doi.org/10.5957/SMC-2009-024
crossref
Remery, G. F. (1974). Mooring forces induced by passing ships. Proceedings of the Offshore Technology Conference (OTC-2066-MS) https://doi.org/10.4043/2066-MS
crossref
Roache, P. J. (1994). Perspective: A method for uniform reporting of grid refinement studies. Journal of Fluids Engineering, 116(3), 405-413. https://doi.org/10.1115/1.2910291
crossref
Song, S., Jung, J. H., & Jung, D. (2024). CFD study of passing ship effects in port. Proceedings of the 2024 Fall Conference of the Korean Society of Ocean Engineers Mokpo, Korea: 96.

Vantorre, M., Verzhbitskaya, E., & Laforce, E. (2002). Model test based formulations of ship-ship interaction forces. Ship Technology Research, 49, 124-141.

Yu, J., Liu, L., Zhang, Z., Yao, C., Feng, D., & Wang, X. (2022). Numerical investigation of passing ship effects in shallow and confined water using Ship-HUST code. Proceedings of the 6th MASHCON International Conference on Ship Manoeuvring in Shallow and Confined Water (, 310-318.

Zheng, Z. Q., Zou, L., & Zou, Z. J. (2022). A numerical investigation on the ship-ship interaction between a passing ship and a moored ship in restricted waterways. Proceedings of the 6th MASHCON International Conference on Ship Manoeuvring in Shallow and Confined Water, 344-355.

Zhou, L., Abdelwahab, H. S., & Guedes Soares, C. (2021). Experimental and CFD investigation of the effects of a high-speed passing ship on a moored container ship. Ocean Engineering, 228, 108914. https://doi.org/10.1016/j.oceaneng.2021.108914
crossref
Zwijnsvoorde, T. V., Delefortrie, G., & Lataire, E. (2022). Passing ship effects in shallow and confined water: open model test data for validation purposes. Proceedings of the 6th MASHCON International Conference on Ship Manoeuvring in Shallow and Confined Water, 254-283.

TOOLS
Share :
Facebook Twitter Linked In Google+ Line it
METRICS Graph View
  • 0 Crossref
  •   Scopus
  • 1,208 View
  • 46 Download


ABOUT
BROWSE ARTICLES
ARTICLE CATEGORY

Browse all articles >

PUBLICATION ETHICS
FOR CONTRIBUTORS
Editorial Office
President Office BD Rm. 1302, 13 Jungang-daero 180beon-gil, Dong-gu, Busan 48821, Republic of Korea
Tel: +82-51-759-0656    Fax: +82-51-759-0656    E-mail: ksoehj@ksoe.or.kr                

Copyright © 2026 by The Korean Society of Ocean Engineers.

Developed in M2PI

Close layer
prev next