Numerical Investigation of Maneuverability in Barge Transportation Using Towing and Pushing Operations

Article information

J. Ocean Eng. Technol. 2026;40(3):286-300
Publication date (electronic) : 2026 June 15
doi : https://doi.org/10.26748/KSOE.2026.018
1Graduate Student, Department of Naval Architecture and Ocean Engineering, Seoul National University, Seoul, Republic of Korea
2Associate Professor, Department of Naval Architecture and Ocean Engineering, Seoul National University, Seoul, Republic of Korea
Corresponding author Bo Woo Nam: +82-2-880-7324, bwnam@snu.ac.kr
Received 2026 March 10; Revised 2026 April 6; Accepted 2026 April 27.

Abstract

Barge transportation using tug–barge systems is widely employed for large cargo transport in rivers and harbor areas, where maneuverability in confined waterways is critical. This study numerically investigates the maneuvering performance of tug–barge systems under pushing and towing operations. Simulations were conducted using a maneuvering model based on the Maneuvering Mathematical Modeling Group framework with experimentally derived hydrodynamic coefficients for each operation mode. For pushing operations, barge configurations were varied by changing the numbers of barges in the longitudinal and transverse directions, whereas for towing operations, the effects of skeg attachment and towline length were examined through turning simulations. The results show that increasing the number of barges generally degrades turning performance, and longitudinal extension causes a greater increase in turning radius than transverse extension. In towing, skeg attachment reduces turning performance by increasing yaw damping and restoring moment, whereas longer towlines enlarge the turning radius by producing a greater negative yaw moment on the tug. Overall, towing yields smaller drift angles and greater rudder effectiveness than pushing, indicating superior turning performance in confined waterways.

Keywords: Towing; Pushing; Skeg; Towline; Tug; Barge

1. Introduction

Barge transportation offers the advantage of transporting large volumes of cargo in a single operation, making it widely used in confined waterways, such as rivers and harbors. Since barges typically lack self-propulsion and rely on external propulsion, the coupling method between the barge and tug directly affects the stability and maneuverability of transport. The two most common operational modes of barges are towing and pushing. In towing operations, a tug pulls a barge via a towline. While this method allows transportation without requiring an additional secure connection system (such as a notch), it has drawbacks, including instability caused by tension fluctuations and inferior maneuvering performance. Conversely, pushing involves a tug propelling the barge from behind as a single unit, which is reported to provide faster response times and superior maneuverability because the thrust is directly transferred to the barge (Sano & Hasegawa, 2015). However, it requires a separate coupling system capable of withstanding substantial loads exerted on the connection interface. Given the recent upward trend in barge traffic volumes and collision incidents, there is a pressing need for studies that systematically investigate the differences in maneuvering performance and stability dictated by these transportation modes.

Regarding towing stability, various experimental and numerical simulation studies have been conducted, primarily focusing on nonlinear behavioral characteristics, the effects of skegs and towlines, and the occurrence of slewing motion. Among notable recent studies, Yasukawa et al. (2006) established a towing simulation based on the Maneuvering Modeling Group (MMG) model, compared the results with experimental data, and evaluated towing stability. Subsequently, Yasukawa et al. (2008) conducted experiments and numerical simulations under wind-load conditions to compare changes in slewing motion according to wind direction and speed, presence of a skeg, and towline length. Hong et al. (2013) investigated the towing stability in waves. Nam et al. (2013, 2014b) compared the MMG model with a cross-flow model; quantitatively examined the effects of varying hydrodynamic coefficients, towing speed, and towline length on slewing motion; and verified their findings through experiments. Nam et al. (2014a) identified and compared the variations in the towing stability and towline tension when multiple tugs towed a barge. Nam et al. (2015) derived linear towing stability criteria under wind load conditions and utilized them to characterize changes in towing stability with respect to wind speed and direction. Furthermore, Nam (2020) identified the nonlinearity of the slewing motion across a broader range of conditions by varying the resistance and tug oscillation in addition to primary towing parameters, such as towline length, towing speed, and hydrodynamic coefficients, and by comparatively analyzing the phase trajectory of the towed vessel. Nam et al. (2022) performed numerical simulations and experiments under disturbance conditions, such as wind and waves, to analyze the variations in towing stability and phase trajectories. Research has also been conducted on barge-turning characteristics and towline dynamics during towing. Fitriadhy and Yasukawa (2010, 2011) analyzed turning performance during barge towing using MMG-based maneuvering equations of motion, while Fitriadhy et al. (2015) derived a linearized equation for the angle between the tug and towline to predict slack towline occurrences, validating this through experiments. Additionally, although Sano and Hasegawa (2015) compared the turning performances of towing and pushing, they did not structurally analyze the differences in maneuverability depending on transport conditions, such as towline length or skeg usage. Baso et al. (2021) experimentally measured the heave and pitch amplitudes of vessels towed in waves. Furthermore, Baso (2022) experimentally verified the changes in towing stability based on the damage conditions of the barge.

However, research on pushing operations has primarily focused on the effects of varying operational parameters, such as barge configuration, loading conditions, and water depth, on maneuvering and resistance performance. King et al. (2008b) analyzed changes in maneuverability based on the number and arrangement of barges during pushing operations using an MMG-based model, and Koh et al. (2008) confirmed that maneuverability varies significantly depending on the arrangement, even when the number of barges remains the same. King et al. (2008a) investigated changes in the turning performance of pushing operations according to water depth. Regarding the loading conditions, Sano et al. (2017) applied computational fluid dynamics (CFD) to calculate the resistance and connection interface flow based on the barge loading conditions in a pushing system coupling a pusher and barges. Subsequently, Sano et al. (2018) conducted circular motion tests (CMT) under various loading conditions. Based on these results, turning, zigzag, and stopping tests were performed using MMG-based numerical simulations to identify the characteristics of the maneuverability changes according to the loading conditions. In studies examining water depth effects in pushing operations, Koh and Yasukawa (2012) conducted rotating arm tests (RAT) on a pushing system at three different water depths and performed numerical simulations to comparatively analyze turning performance. Maimun et al. (2011) compared the hydrodynamic coefficients calculated from planar motion mechanism (PMM) tests with the results from empirical formulas. They verified these findings through MMG-based simulations and compared them with experimental data. Bravo et al. (2018) evaluated response amplitude operators (RAOs) and connection loads according to the wave direction through a frequency-domain analysis of the pushing system. Delefortrie et al. (2022) conducted model tests by varying the number of barges and loading conditions to measure 6-degree-of-freedom forces. Wang and Sano (2025) assessed the seakeeping performance of a multi-barge pushing system via regular wave experiments, obtained the RAOs for the motion of each barge and tug, as well as the connection loads, and compared the effects of increasing the number of barges.

In this study, numerical simulations were conducted to directly compare the maneuverability of the towing and pushing transportation modes previously examined individually and to understand their fundamental characteristics. For pushing, simulations were performed using the model test data, thrust, and rudder force coefficients obtained by King et al. (2008b), whereas for towing, the model test data reported by Fitriadhy et al. (2015) were used. Through numerical simulations, the turning performance of towing with and without a skeg was comparatively analyzed, along with the turning performance and physical forces of both the towing and pushing operations. Ultimately, this study aimed to clarify the effects of skeg attachment during barge transport, evaluate the maneuvering performance of each mode, and identify the underlying physical forces and quantities driving these characteristics.

2. Methodology

2.1 Pushing Model

In this study, maneuvering equations of motion based on the Maneuvering Modeling Group (MMG) model were applied to simulate barge behavior during pushing operations (King et al., 2008b). As it was assumed that the tug and barge were completely fixed during pushing, the integrated tug–barge system was regarded as a single floating body. Accordingly, a single-body-fixed coordinate system was utilized, as shown in Fig. 1, and the equations of motion for the coupled system can be expressed as those for a single floating body, as shown in Eq. (1):

Fig. 1

Coordinate system of pushing simulation

(1) (m+mx)u˙-(m+my)vr=XH+XP+XR(m+my)v˙+(m+mx)ur=YH+YR(Iz+Jz)r˙=NH+NR-(YH+YR)xG}

where m and Iz represent the mass and yaw moments of inertia, respectively, of the entire integrated system. The terms mx, my, Jz correspond to the added mass coefficients in the surge, sway, and yaw directions, while u, v, r denote the surge velocity, sway velocity, and yaw rate at the center of gravity, respectively. The hydrodynamic forces acting on the hull, XH,YH,NH are expressed by Eq. (2):

(2) XH=12ρLd U2(Xββ′βm′2+Xβr′βmr′+Xrr′r′2)+12ρLdXuu′u2YH=12ρLdU2(Yβ′βm+Yr′r′+Yβββ′βm3+Yββr′βm2r′)NH=12ρL2dU2(Nβ′βm+Nr′r′+Nβββ′βm3+Nββr′βm2r′)}

In these equations, ρ is the fluid density, and L, d are the length and draft of the integrated system. U=u2+v2 is the total speed of the vessel speed of the vessel, and Bm = tan−1(−vm/U ) corresponds to the drift angle at the midship. Here, vm = v−xgr is the lateral velocity at the midship, and r′ is the nondimensionalized yaw rate (r′ = rL/U ).

In pushing operations, barges of various widths and lengths are used, or multiple barges are operated in a connected configuration. To examine these effects, this study analyzed the influence of barge arrangement on turning performance by considering the nine barge configurations proposed by Koh et al. (2008), as shown in Fig. 2, and increasing the number of barges by up to three in both the transverse and longitudinal directions. According to the arrangement, the hydrodynamic derivatives were identical to those presented by Koh et al. (2008).

Fig. 2

Various barge configurations in pushing operations

The thrust and rudder models used in the simulation are the same as those employed by Koh et al. (2008), as shown in Eqs. (3) and 4, respectively. Because this study considered a propulsion system with twin screws and twin rudders, the propeller and rudder forces were expressed as the resultant force of thrust from the two propellers and the forces from the left and right rudders. The port and starboard sides are denoted by subscripts p and s, respectively, and the moment generated by the y-axis distance is not considered. In addition, the thrust and rudder force coefficients for the port and starboard sides were assumed to be identical.

(3) XP=(1-tpp)ρnpp2Dpp4KTp+(1-tps)ρnps2Dps4KTs
(4) XR=-(1-tRp)FNpsin(δp)-(1-tRs)FNssin(δs)YR=-(1+aH)FNpcos(δp)-(1-aH)FNscos(δs)NR=-(xR+xHaH)FNpcos(δp)-(xR+xHaH)FNscos(δs)}

where Dp is the propeller diameter, n the number of propeller revolutions per second (rps), and tp the thrust deduction factor. KT is the thrust coefficient measured in the propeller open-water tests and is expressed by Eq. (5):

(5) KT=-0.3260pJP-0.2005JP+0.5234p-0.0398

In this context, JP is the propeller advance ratio, and p denotes the propeller pitch ratio, expressed as follows:

(6) JP=u(1-wp)nDp

wP is the wake coefficient determined using Hirano’s formula, as shown in Eq. (7):

(7) wP=wP0exp (C1βP2)

Where wP0 is the propeller wake at the initial advance speed, and βP=β-lP′r′ represents the drift angle at the propeller position. C1 is the correction factor.

δ is the rudder angle, tR is a deduction factor adjusting the effective transfer rate of longitudinal force generated by the rudder, and aH is a coefficient representing the additional lateral force due to rudder–hull interaction, xH is the moment arm of this additional lateral force. xR denotes the moment arm of lateral rudder force YR . The rudder normal force FN is expressed by Eq. (8):

(8) FN=12ρARUR2fαsinαR

In this context, AR is the rudder area, fα=6.13Λ2.25+Λ corresponds to the lift gradient coefficient of the rudder, and the rudder inflow velocity UR is expressed as in Eq. (9). where uR, vR represent the longitudinal and lateral components of the rudder inflow velocity, respectively. αR is the effective inflow angle and is expressed as in Eq. (10). The thrust and rudder force coefficients used in the simulation were adopted from the values reported by Koh et al. (2008).

(9) UR=uR2+vR2
(10) αR=δ-tan-1vRuR

2.2 Towing Model

In towing operations, because the tug and barge move as independent rigid bodies, separate body-fixed coordinate systems are utilized for each hull, and the equations of motion are described independently (Fitriadhy et al., 2015). The equations of motion for the tug (i = 1) and barge (i = 2) are shown in Eqs. (11) and (12), respectively. The inertial characteristics of each hull are represented by hull mass mi and yaw moment of inertia Izi, where mxi, myi, Jzi correspond to the added masses in the surge, sway, and yaw directions of the hull, respectively. ui, vi, ri correspond to the surge velocity, sway velocity, and yaw rate at the center of gravity, respectively. at the center of gravity, respectively. XHi, YHi, NHi represent the hydrodynamic forces acting on each hull; while XP is the thrust from the propeller; XR, YR, NR are the rudder forces; and XTi, YTi, NTi represent the forces and moments caused by the tension acting at the towline connection points. At this time, thrust and rudder forces exist in the case of the tug (i = 1) but do not exist for the barge (i = 2). Therefore, whereas the equations of motion for the tug include thrust and rudder terms in addition to hull hydrodynamic forces and towline tension, only hydrodynamic forces and tension exist in the equations of motion for the barge.

(11) (m1+mx1)u˙1-(m1+my1)v1r1=XH1+XP+XR+XT1(m1+my1)v˙1+(m1+mx1)u1r1=YH1+YR+YT1(Iz1+Jz1)r˙1=NH1+NR-(YH1+YR)xg1+NT1}
(12) (m2+mx2)u˙2-(m2+my2)v2r2=XH2+XT2(m2+my2)v˙2+(m2+mx2)u2r2=YH2+YT2(Iz2+Iz2)r˙2=NH2-(YH2+YR)xg2+NT2}

The hydrodynamic forces acting on the hulls of the tug (i = 1) and the barge (i = 2) are expressed by Eq. (13).

(13) XHi=12ρLidiUi2(Xvvi′vi′2+Xvri′vi′ri′+Xrri′ri′2)-Xuuiui2YHi=12ρLidiUi2(Yvi′vi′+Yri′ri′+Yvvvi′vi′3+Yvvri′vi′2ri′+Yvrri′vi′ri′2+Yrrri′ri′3)NHi=12ρLi2diUi2(Nvi′vi′+Nri′ri′+Nvvvi′vi′3+Nvvri′vi′2ri′+Nvrri′vi′ri′2+Nrrri′ri′3)}

Three types of vessels–tugs, barges without skegs, and barges with skegs - were used in the simulation, and their hydrodynamic derivatives were identical to those used by Fitriadhy et al. (2013). The skegs were attached to both ends of the barge stern, with a length of 6.1 m, a maximum height of 1.5 m, and a thickness of 0.1 m.

The thrust and rudder models used in the simulation are identical to those used by Fitriadhy et al. (2015), as shown in Eqs. (14) and (15), respectively.

(14) XP=(1-tpp)ρnpp2Dpp4KTp+(1-tps)ρnps2Dps4KTs
(15) XR=-(1-tRp)FNpsin(δp)-(1-tRs)FNssin(δs)YR=-(1-aH)FNpcos(δp)-(1+aH)FNscos(δs)NR=-(xR+xHaH)FNpcos(δp)-(xR+xHaH)FNscos(δs)}

where Dp is the propeller diameter, n is the propeller revolution, and tp is the thrust deduction thrust deduction factor. KT is the thrust coefficient measured in the propeller open-water tests and is expressed by Eq. (16). The remaining equations were identical to those used for pushing in Section 2.1; however, the thrust and rudder force coefficients used in the simulation were adopted from the values presented by Fitriadhy et al. (2015). Furthermore, for a direct comparison between the pushing and towing in Section 3.2, a comparison was performed after unifying the thrust and rudder models with those used in the towing model.

(16) KT=-(0.6573(p-0.6)+0.3958)JP+2.2693(p-0.6)+0.6783

Fig. 3 shows a diagram representing the coordinate system of the towing system. The tug (i = 1) and barge (i = 2) have fixed body-fixed coordinate systems (xi, yi), and the towline connects the tug-side connection point (xtow, ytow) to the barge-side connection point (xtowed, ytowed). The heading angle of each hull is defined as φi, and the towline angle is denoted by θ. Additionally, ltug and lbarge denote the distances between the towline connection point and the center of gravity for each vessel, and the tension in the towline direction acts as a force component in the body-fixed coordinate system of each hull. In this study, the towline tension was simulated using a simple spring model. For the spring constant k, a value of 125 kN/m was used, which was converted to full–scale from the model–scale value of 50 N/m used by Nam et al. (2013), and for the damping coefficient b, a value of 25 kN·s/m was used at the same ratio. If the instantaneous length of the towline is LT and the initial towline length is Ltowline, then the tension T is expressed as in Eq. (17), considering only tension during elongation. In this case, the instantaneous towline length LT is defined as the distance between connection points (xtowed, ytowed) and (xtow, ytow) with each hull, as shown in Eq. (18).

Fig. 3

Coordinate system of towing simulation

(17) T={k(Lt-Ltowline)+bL˙T(if LT>Ltowline)0(if LT≤Ltowline)
(18) LT=(xtow-xtowed)2+(ytow-ytowed)2

The towline force components and moments XTi, YTi, NTi acting on the tug and barge can be expressed as shown in Eq. (19) and Eq. (20), respectively:

(19) XT1=Tcos(σ)YT1=Tsin(σ)NT1=ltug YT1}
(20) XT2=Tcos(γ)YT2=Tsin(γ)NT2=lbarge YT2}

Here, σ, γ represent the relative angles of the towline with respect to the heading angles of the tug and the barge, respectively, and signify the directional angles of the towline as viewed from each vessel’s body–fixed coordinate system. As shown in Fig. 2, the directional angle of the towline is defined as σ = φ1 −θ for the tug and γ = θ−φ2 for the barge.

2.3 Target Vessels

The target vessels utilized in this study were the tug and barge models commonly used by Koh et al. (2008) and Fitriadhy et al. (2015). In this case, the barge is a catamaran-type barge consisting of two barges connected in a transverse direction. For the pushing operations, the system was operated in a configuration in which the catamaran barge and tug were connected in the longitudinal direction. Table 1 lists the dimensions of the target vessels.

Dimensions of target vessels

3. Results and Discussion

3.1 Pushing Simulation

To verify the reliability of the numerical pushing simulation established in this study, a direct comparison was performed with the simulation results presented by King et al. (2008). The test condition is a case where one tug is coupled with one barge in a pushing mode, and a 20° turning test and a 10°/10° zigzag test were performed while maintaining a revolution of 5 rps and a pitch ratio of 0.612 to achieve an advance speed of 7 knots (3.6 m/s) without a rudder angle. For comparison, the trajectories of the turning test and the time series of the heading angle and rudder angle of the zigzag test were confirmed, and maneuvering performance indices such as advance, tactical diameter, transfer, 1st overshoot angle, and response time were quantitatively compared. Fig. 4(a) shows the turning trajectory of the pushing simulation, and Fig. 4(b) shows the time-series graphs of the heading and rudder angles in the zigzag test. In Fig. 4(a), the blue solid line represents the current simulation results and the red dotted line represents the results presented by King et al. (2008b). In the turning test, a circular trajectory corresponding to a steady turning diameter of approximately 500 m was observed; in the zigzag test, the 1st overshoot angle was approximately 3.5° and the 2nd overshoot angle was approximately 5°. Fig. 5 presents a bar graph that quantitatively compares the results of the turning and zigzag tests. The turning test characteristics of the pushing simulation, such as advance, tactical diameter, and transfer, showed small errors of approximately 1.9–3.3% compared with the results of King et al. (2008b). In the zigzag test, small errors of 2.8% and 1.3% were observed for the 1st overshoot angle and response time, respectively. Overall, the results of the two simulations exhibited a high degree of agreement. Additionally, to maintain an advance speed of 7 knots (3.6 m/s) for each configuration, this study assumed that the propeller revolution speed n was fixed, and the pitch ratio of the controllable pitch propeller (CPP) was increased, as in the study by Koh et al. (2008). Table 2 lists the pitch ratios used based on the barge arrangement.

Fig. 4

Comparison of turning and zigzag maneuvers in the pushing simulation

Fig. 5

Quantitative comparison of turning and zigzag maneuver characteristics

Pitch ratio for each configuration

Figs. 6 (a)–(c) illustrate the turning motion trajectories over time for a single barge (11BP), a case where the number of barges increased in the transverse direction (31BP), and a case where it increased in the longitudinal direction (13BP). The simulation conditions included an advance speed of 7 knots (3.6 m/s) and a rudder angle of 20°. In the case of the single barge shown in Fig. 6(a), it is confirmed that it reaches the vicinity of 400 m in the x-direction, which corresponds to the advance distance, within 3 min. In the cases of 31BP and 13BP, in which the number of barges increased to three, the advance distance and time to reach the advance distance increased. It can be confirmed that 31BP, corresponding to Fig. 6(b), reached the vicinity of 600 m in the x-direction, corresponding to the advance distance, at approximately 4 min, whereas 13BP in Fig. 6(c) did not reach the position corresponding to the advance distance even after 5 min.

Fig. 6

Turning trajectories with time snapshots for three representative barge configurations

Fig. 7 (a) and (b) compare the nondimensionalized turning motion trajectories when the number of barges is increased in the transverse and longitudinal directions, respectively, in a pushing situation. To fairly compare the increase in the length and width of the vessel, nondimensionalization was performed using the length of a unit barge rather than the total length of each configuration. Overall, as the number of barges increased, the scale of the turning trajectory tended to increase; in particular, the expansion of the turning trajectory appeared larger in the longitudinal direction (Fig. 7(b)) compared to the transverse direction (Fig. 7(a)). When the number of barges was increased to two and three in the transverse direction, the steady turning radius increased by 30.7% and 90.6%, respectively, whereas in the case of a longitudinal increase, it increased by 52.8% and 157.1%, respectively. That is, the longitudinal increase showed a turning performance deterioration approximately 1.7 times greater than the transverse increase. Figs. 8 (a) and (b) show bar graphs comparing the advance and tactical diameters of the nine barge arrangements presented in Fig. 5, respectively. Both turning characteristics showed a tendency to increase as the number of barges increased. In particular, it was found that the longitudinal increase had a greater effect on turning performance than the transverse increase. When the number of barges in the longitudinal direction increased three-fold from 11BP, which had one barge in the transverse direction, to 13BP, the number of barges increased by two, and the advance distance and tactical diameters increased by 124.2% and 127.5%, respectively. Conversely, when the number of barges in the longitudinal direction increased three-fold from 31BP, which had three barges in the transverse direction, to 33BP, the number of barges increased by six, but the growth rates were 34.88% and 39.6%, respectively. As a result, the advance distance and tactical diameter of 33BP, which transports nine barges, were 6.78% and 11.2% smaller than those of 13BP, which transports three barges, respectively, indicating superior turning performance. To clearly analyze the cause of this, the hydrodynamic forces acting on the hull and rudder were compared.

Fig. 7

Comparison of turning trajectories for different barge configurations

Fig. 8

Non-dimensional turning maneuver characteristics for the 9 barge configurations

Table 3 lists the changes in the hydrodynamic derivatives in the transverse and yaw directions according to the change in the barge arrangement configuration. The analysis confirmed that the main factors contributing to turning performance differed depending on the arrangement direction. First, the linear transverse damping force Yβ′ increases sharply by approximately 76.6% when increasing in the transverse direction (31BP), acting as a major cause of turning performance degradation. On the other hand, when increasing in the longitudinal direction (13BP), Yβ′ actually shows a slight decreasing tendency, and instead, the nonlinear component Yβββ′ increases by approximately 50.2%, suggesting that the change in turning performance according to the arrangement cannot be explained by a simple linear model alone. Yr′ and Nβ′, which represent the coupling effects of longitudinal and yaw motions, showed a decreasing tendency in all configurations. In particular, when increasing in the longitudinal direction, the decrease in Yr′ becomes significantly larger than that in the transverse direction, which is considered to affect the turning performance through changes in the lateral pressure during turning. In the case of the yaw restoring moment Nβ′ and the nonlinear term Nβββ′, the decrease was prominent when increasing in the longitudinal direction. Especially when increasing in the transverse direction, Nβββ′ increases significantly to a level of about 141.6%, causing an increase in turning performance by augmenting the yaw damping force caused by transverse motion. Additionally, the absolute value of the yaw damping derivative Nr′ increased by approximately 202.5% when increasing in the transverse direction, which was analyzed as a factor that directly increased the turning resistance and caused a decrease in the turning performance in that configuration.

Comparison of hydrodynamic derivatives for three barge configurations

Table 4 shows a comparison of the steady-state values of the nondimensionalized longitudinal and transverse hydrodynamic forces, rudder normal force, drift angle, and effective rudder inflow angle for the cases where the number of barges was increased to three in the transverse direction (31BP) and three in the longitudinal direction (13BP) with the results of a single barge (11BP). At this time, forces were nondimensionalized by 12ρLd U2 and moments by 12ρL2d U2 can be confirmed from the longitudinal hydrodynamic force, a larger longitudinal hydrodynamic force occurs in 31BP, the transverse increase, compared to 13BP, the longitudinal increase. This is because the longitudinal fluid resistance component acting on the lower hull increases approximately three-fold as the barges are connected in the transverse direction. 31BP, which has a relatively large longitudinal resistance, applies a pitch ratio approximately 25% larger than that of 13BP to maintain the same speed, which increases the propeller inflow velocity uR as the pitch ratio increases under the condition that the propeller revolution speed n is the same. Therefore, an increase in the rudder inflow velocity leads to an increase in the rudder normal force, as listed in Table 4. That is, when the number of barges increases in the transverse direction, the rudder force increases under the same vessel speed condition, resulting in superior turning performance compared to arranging the same number of barges in the longitudinal direction. As previously explained, because the increase in the number of transverse barges increases resistance, the longitudinal speed decreases more significantly in 31BP and the drift angle B = tan−1(−v/U ) becomes larger. It can be confirmed that the steady drift angle at 31BP is approximately 19.6°, which is approximately 32% larger than the approximately 15° drift angle at 13BP. In response to this increase in the drift angle, 31BP shows a larger value than 13BP in the transverse hydrodynamic force, confirming that an increase in the number of transverse barges increases both the drift angle and the transverse hull force. Furthermore, consistent with what was confirmed in the steady −state values of the effective rudder inflow angle, the effective rudder inflow angle αR appears larger in 31BP, where the drift angle was larger. This is contrary to the general tendency in which the effective inflow angle decreases as the drift angle increases, and this difference can be explained by the difference in the rudder inflow velocity uR . When the required thrust increases during transverse expansion, the rudder inflow velocity increases; at this time, in the effective inflow angle αR = δ−tan−1(vR/uR ), if uR is increases, tan−1(vR/uR ) decreases, and thus αR also increases. Consequently, when the number of barges is increased in the transverse direction, both the rudder inflow velocity and effective rudder inflow angle increase, and an improvement in turning performance occurs because of this increase in rudder force, resulting in the transverse expansion arrangement exhibiting superior turning performance compared with the longitudinal expansion arrangement.

Comparison of hull force, drift angle and rudder in-flow angle for three barge configurations

3.2 Towing Simulation

The towing simulation was validated using the turning test results presented by Fitriadhy et al. (2015). Figs. 9(a) and (b) show the turning motion trajectory and time series of the tension under the conditions of an advance speed of 7 knots (3.6 m/s), a rudder angle of 15°, and a towline length of LT = 3Lpp. At this time, the propeller revolutions to maintain the advance speed corresponded to 5 rps, and the pitch ratio was 0.4601. Fig. 9(a) compares the turning motion trajectories, where the dotted line represents the trajectory of the tug, and the solid line represents the trajectory of the barge. In this case, the steady turning radius of the tug was approximately 310 m, and that of the barge was approximately 280 m, confirming that the tug turning with its own thrust and rudder force exhibited a larger turning radius compared to the barge turning solely by tension. This is because, as shown in Fig. 3, the barge is located on the starboard side of the tug during starboard turning. This is because as the towline becomes longer, the angle σ between the tug and the towline increases and the transverse distance between the tug and the barge increases, causing the barge to turn inside the turning trajectory of the tug. As a result of analyzing the errors of the two numerical simulations, in terms of the turning trajectory, the advance distance, which is highly influenced by the initial behavior, showed a larger error than the tactical diameter, although the overall errors were very small at 3.3% and 1.3% for the advance distance and tactical diameters, respectively. Fig. 9(b) shows the time series of tension, and it can be confirmed that at the beginning of turning, increases and decreases in tension are clearly observed according to the transient behavior of the two floating bodies, which then gradually stabilize upon entering the steady turning stage. The tension peaks due to transient behavior occur at two time points: the first peak occurs when the tug initially starts from a stationary state and momentarily pulls the towline, and the second peak occurs near 120 s as the separation distance between the tug and barge widens at the point where the tug begins turning, resulting in maximum tension. These characteristics can also be confirmed in the turning trajectory shown in Fig. 9(a), where the transient interval corresponding to 50–150 s represents the section that initially deviates from the steady turning trajectory. In the tension response acting on the towline in the two numerical simulations, while Fitriadhy et al. (2015) showed a maximum tension of 13.6 t at 105.5 seconds, this study yielded a (a) Turning motion trajectory (b) Time histories of tension maximum tension of 14.74 t at 121.8 seconds, corresponding to errors of 15.5% in response time and 8.4% in the maximum value. Errors in this initial behavior are considered to stem from the difference between the lumped-mass model utilized by Fitriadhy et al. (2015) and the simple spring-based towline model of this study. However, the tension in the steady turning state was 8.73 t for Fitriadhy et al. (2015) and 8.63 t in this study, showing an error of approximately 1.1%, indicating that the simulation in this study demonstrates sufficient accuracy in an engineering sense.

Fig. 9

Validation of the towing simulation against the results of Fitriadhy et al. (2015)

In the case of towing, the turning characteristics varied significantly depending on the towline length and the presence of skegs. Therefore, this study aimed to examine the turning performance characteristics according to the towline length and the presence of skegs, and a comparison was performed alongside the turning test results using pushing. Figs. 10(a) and (b) show graphs comparing the nondimensionalized turning motion trajectories of towing and pushing according to the presence of skegs and the towline length. Nondimensionalization was performed using the length of the barge. The simulation time was 1000 s, the advance speed was 7 knots (3.6 m/s), and the rudder angle was 15°. The barge-turning performance was compared when the towline length was set to two and three times the barge length, and according to the presence of skegs. In Figs. 10(a) and (b), it can be confirmed that the barge-turning radius increases with towing as the tow line length increases. In the comparison based on the presence of skegs, the turning radius in Fig. 10(b) without skegs is larger than that in Fig. 10(a) with skegs. Furthermore, it can be confirmed that the barge turning radius tends to increase or decrease in the same trend as the turning radius of the tug. To quantitatively verify this trend, Figs. 11(a) and (b) present graphs comparing the nondimensionalized steady turning radius and transfer. For towing, only the steady turning radius and transfer of the barge were plotted. With skegs, the steady turning radius was 20.9% and 6.7% smaller compared with pushing at towline lengths of 2Lpp and 3Lpp, respectively. Without skegs, the turning radius was 4.5% smaller than (a) Towing with skegs (b) Towing without skegs pushing when the towline length was 2Lpp, but it increased significantly to 21.7% when the towline was lengthened to 3Lpp. That is, it can be confirmed that the attachment of skegs improves turning performance, whereas increasing the towline length degrades turning performance. Meanwhile, in terms of transfer, a trend opposite to that of the steady turning radius was observed. While transfer without skegs appeared 57.3% and 59.2% smaller than pushing with skegs, it only decreased by 38.9% and 32.1%, respectively, showing a larger transfer than without skegs. This is thought to be because skegs increase the damping and restoring forces in the yaw direction to improve towing stability, but simultaneously suppress heading angle changes in the initial behavior, resulting in a larger transfer. Additionally, the transfer in towing was observed to be consistently smaller than that in pushing, regardless of the presence of skegs or the towline length. This is because, unlike pushing, where the tug and barge are combined, resulting in a large yaw moment of inertia, in towing, only the tug begins turning, leading to a faster initial heading angle development. As the tug heading angle increases, the direction of tension applied to the barge changes, increasing the transverse tension on the barge. This results in a large yaw moment being applied to the barge, and its heading angle rapidly increases, leading to a small transfer.

Fig. 10

Comparison of turning trajectories of towing with different towline lengths with and without skegs

Fig. 11

Effect of skeg and towline length on the turning performance of barge compared with pushing

To analyze turning performance variations according to the presence of skegs, Table 5 presents a comparison of the steady-state values of hydrodynamic derivatives in the transverse and yaw directions, the nondimensionalized yaw moment, and γ according to the presence of skegs. The yaw moment was nondimensionalized by 12ρL2dU2. It can be confirmed that as skegs are attached, the absolute values of Yv′ and Nr′, which correspond to damping and restoring forces in the transverse and yaw directions, increase. This is a direct cause of reduced turning performance when skegs are attached in a turning situation. Furthermore, for a barge without skegs Nv′=-0.1160 and Nr′=-0.0237, while for a barge with skegs Nv′=-0.0691 and Nr′=-0.0542 respectively, indicating that |Nv′| decreases and |Nr′| increases when skegs are attached. In a steady starboard turning situation, where the transverse velocity v < 0 and yaw rate r > 0, these changes in the hydrodynamic derivatives cause a decrease in the yaw hydrodynamic force. In the steady turning state, the nondimensionalized yaw moment is 0.0303 without skegs and −0.0097 with skegs. This implies that the skegs significantly reduced the yaw hydrodynamic force, thereby decreasing the heading angle. However, despite this reduction in turning performance from a hydrodynamic force perspective, the attachment of skegs actually increased the turning performance. The reason why skeg attachment reduces the turning radius can be confirmed from the steady-state values of γ in Table 5. γ is a variable that determines the direction in which towline tension acts on the barge; for a barge without skegs, a larger yaw moment acts causing the heading angle to increase more, and as a result, γ the angle between the towline and the barge heading, appears larger than in the case with skegs. However, this results in a tension-induced moment acting in the direction opposite to the barge turning direction when skegs are absent, thereby increasing the turning radius. For skegs, the tension-induced moment acts in a direction that aids turning, causing the turning radius to decrease. Furthermore, as the magnitude of γ increases, the longitudinal component of tension (Tx = Tcosγ) decreases and the transverse component (Ty = Tsinγ) increases. This causes the tension transmitted to the barge to be more transversely dispersed, resulting in a decrease in the advance speed. Figs. 12(a) and (b) present snapshots showing the difference in γ according to the presence of skegs, comparing the angles at the moment the transverse velocity of the tug is zero. As previously explained, skegs increase yaw restoring and damping forces to suppress the development of the heading angle, confirming that γ is maintained relatively small when skegs are attached.

Effect of skeg on hydrodynamic derivatives, yaw hull moment and γ

Fig. 12

Snapshots of turning trajectories with and without skegs

The turning characteristic variations according to the towline length can be confirmed by the change in the angle between the tug and the towline. Fig. 13(a) is a time series graph comparing γ and σ according to towline length. When the towline length increased from 2Lpp to 3Lpp, the variation in the angle γ between the barge and the towline was small at less than 1°, whereas the angle σ between the tug and the towline changed significantly from −31.57° to −35.37°. That is, as the towline length increases, the magnitude of σ increases, leading to an increase in the transverse tension component and the yaw moment acting on the tug. In this case, because the moment applied by the tension to the tug is in the negative direction, the yaw rate of the tug decreases, resulting in a larger turning radius. Fig. 13(b) shows a time-series graph plotting the heading angles of the barge and tug with pushing. Up to approximately 40 s, as barge turning does not occur, it can be confirmed that the tug heading angle increases identically, regardless of the towline length. Subsequently, as the barge begins turning, differences according to the towline length appear, with the heading angles of the tug and barge at the shorter length of 2 Lpp increasing more rapidly. As previously explained, when the towline length increases, the tug yaw rate decreases, leading to differences in the tug heading angle. It can be confirmed that in pushing, the heading (a) Towing angle γ, σ (b) Heading angle φ angle increases upon starting the turn, but at a slower rate compared to towing. Figs. 14(a) and (b) show snapshots of the steady turning situations for the pushing and towing modes, respectively. As can be seen in Fig. 14(a), the heading angle develops significantly in pushing, and accordingly, the drift angle β also becomes large. Conversely, in the towing shown in Fig. 14(b), the heading-angle variation is restricted, maintaining a relatively small drift angle. This difference stems from the difference in yaw moments between the two transport modes. When pushing, the moment arm between the rudder point of application and the center of gravity was long (63.24 m), causing a large rudder moment. In contrast, in towing, the distance between the rudder point of application and the center of gravity is short (22.23 m), and, as shown in Fig. 14(b), the moment due to the towline tension acts in a direction that cancels out the rudder moment. Consequently, in towing, the development of the heading angle is suppressed and the drift angle is maintained small, and this difference in the drift angle acts as a major factor determining the difference in turning performance between the two methods.

Fig. 13

Effect of towline length on the time histories of towing angles and heading angle

Fig. 14

Snapshots of turning trajectories for pushing and towing conditions

Table 6 compares the drift angle, effective rudder inflow angle, and nondimensionalized transverse rudder force for the tug during towing and pushing. Transverse rudder force was nondimensionalized by 12ρLd U2. The drift angles in towing at towline lengths of 2Lpp and 3Lpp were 5.26° and 4.26°, respectively, which were 73.34% and 67.15% smaller than those at 16 ° in pushing. As the drift angle is maintained small, the transverse velocity component of the rudder inflow decreases and the longitudinal component increases, and consequently, the effective rudder inflow angle αR appears larger than the 5.54° in pushing. It can be confirmed that the effective rudder inflow angle αR in towing was 10.94° and 11.48°, which are approximately 1.97 and 2.07 times larger than that of pushing. With the increase in the effective inflow angle, the rudder normal force and transverse rudder force, which are proportional to sin αR, also increase, meaning that towing has higher control force efficiency compared to pushing.

Effect of towline length on drift angle, rudder in-flow angle and sway hull force

4. Conclusion

In this study, numerical simulations using an MMG-based maneuvering model were performed for pushing and towing, two representative operation modes for transport barges, and the turning performance and physical mechanisms in each transport mode were systematically reviewed. To this end, changes in the hydrodynamic forces, drift angles, and towline angles according to major design variables such as the presence of skegs, towline length, and barge arrangement configuration were analyzed.

  1. In the pushing mode, changes in thrust emerged as the primary cause of the difference in turning performance. When the number of barges increased in the transverse direction, the hull resistance increased significantly, which led to an increase in the thrust required to maintain the same speed, resulting in an increase in the rudder force owing to the increased rudder inflow velocity. In the case of 31BP, which represents a transverse increase, a pitch ratio approximately 30% larger than that of 13BP, a longitudinal increase, was required. Because of this increase in the control force, the transverse increase showed a turning performance approximately 1.7 times superior to the longitudinal increase.

  2. In the towing mode, the presence of skegs and towline length emerged as the main factors determining the turning performance. The skeg is an appendage that improves towing stability by increasing yaw damping and restoring forces; in turning situations, it improves both turning performance and advance speed by keeping the angle (γ) between the barge heading and the towline small, thereby increasing the longitudinal component of tension. Conversely, as the towline length increased, the negative tension moment acting on the tug increased, which decreased the yaw angular velocity and consequently increased the turning radius.

  3. As a result of the direct comparison between pushing and towing, towing tended to exhibit a relatively superior turning performance by lowering the drift angle by up to 73% compared with pushing, as the tension moment offsets the rudder moment, thereby increasing the rudder force efficiency by more than twofold. Furthermore, owing to the interference of the barge during the initial behavior, the transfer of towing was always smaller than that of pushing.

In this study, the effects of barge transport mode, arrangement, and presence of appendages on turning performance were quantitatively compared, and their physical causes were analyzed. These results are expected to serve as useful basic data for establishing design and operational strategies for barge transport systems operating in confined waterways. Future research requires a high-accuracy towline dynamics analysis that can more realistically simulate towline behavior, and there are plans to perform additional numerical simulations for complex transport scenarios where towing and pushing are performed simultaneously, considering actual operation conditions.

Notes

Bo Woo Nam served as an editorial board member of the Journal of Ocean Engineering and Technology. However, he had no role in the decision to publish this article. No potential conflict of interest relevant to this article was reported.

This research was supported by a Korea Agency for Infrastructure Technology Advancement (KAIA) grant funded by the Ministry of Land, Infrastructure, and Transport (Grant RS-2023-00250727) through the Korea Floating Infrastructure Research Center at Seoul National University. This work was also supported by the Korea Institute for Advancement of Technology (KIAT) grant funded by the Korean Government (MOTIR) (RS-2023-KI002688, HRD Program for Industrial Innovation). This research was part of a project titled ‘Fostering Talent in Advanced Ship Blue Tech (RS-2025-02221147)’, funded by the Ministry of Oceans and Fisheries, Korea.

References

Baso S. 2022;Experimental investigation of course stability on a barge during damaged conditions. SINERGI 26(2):173–184. https://doi.org/10.22441/sinergi.2022.2.006.
Baso S, Fitriadhy A, Anggriani A. D. E, Rosmani A. A, Nugraha A. M. 2021;Investigating the motions’ characteristics of a towed barge in extreme heading wave. IOP Conference Series: Earth and Environmental Science 799:012002. https://doi.org/10.1088/1755-1315/799/1/012002.
Bravo C. S, Hong S. W, Nam B. W. 2018. October. An investigation on the performance of a pusher-barge system in regular waves. In : In the 13th ISOPE Pacific/Asia Offshore Mechanics Symposium (p. ISOPE-P-18-050). ISOPE;
Delefortrie G, Villagomez J, Verwilligen J. 2022;Maneuvring behavior of push convoys in different barge configurations. Journal of Ship Research 66(3):231–249. https://doi.org/10.5957/JOSR.1220005.
Fitriadhy A, Yasukawa H, Koh K. K. 2013;Course stability of a ship towing system in wind. Ocean Engineering 64:135–145. https://doi.org/10.1016/j.oceaneng.2013.02.001.
Fitriadhy A, Yasukawa H, Maimun A. 2015;Theoretical and experimental analysis of a slack towline motion on tug-towed ship during turning. Ocean Engineering 99:95–106. https://doi.org/10.1016/j.oceaneng.2015.03.008.
Fitriadhy A, Yasukawa H, Yusaku M. 2010. June. Turning characteristic of a tow ship in towing system. In : In the 20th International Offshore and Polar Engineering Conference (p ISOPE-I-10-366). ISOPE;
Fitriadhy A, Yasukawa H, Yusaku M. 2011;January). Course stability of a ship towing system. Ship Technology Research 58(1):4–23. https://doi.org/10.1179/str.2011.58.1.001.
Hong S. Y, Nam B. W, Kim J. H, Park J. Y. 2013. June. A study on towing characteristics of a transportation barge in waves. In : In the 23th International Offshore and Polar Engineering Conference (p. ISOPE-I-13-351). ISOPE;
King K. K, Yasukawa H, Hirata N. 2008a. June. Shallow water effect on turning motion of a pusher-barge system. In : In the 4th Asia-Pacific Workshop on Marine Hydrodynamics (APHydro 2008). Taipei.
King K. K, Yasukawa H, Hirata N, Kose K. 2008b;Maneuvering simulations of pusher-barge systems. Journal of marine science and technology 13:117–126. https://doi.org/10.1007/s00773-007-0267-4.
Koh K. K, Yasukawa H. 2012;Comparison study of a pusher–barge system in shallow water, medium shallow water and deep water conditions. Ocean engineering 46:9–17. https://doi.org/10.1016/j.oceaneng.2012.03.002.
Koh K. K, Yasukawa H, Hirata N. 2008;Hydrodynamic derivatives investigation of unconventionally arranged pusher-barge systems. Journal of marine science and technology 13(3):256–268. https://doi.org/10.1007/s00773-008-0004-7.
Maimun A, Priyanto A, Muhammad A. H, Scully C. C, Awal Z. I. 2011;Manoeuvring prediction of pusher barge in deep and shallow water. Ocean engineering 38(11–12):1291–1299. https://doi.org/10.1007/s00773-017-0485-3.
Nam B. W. 2020;Numerical investigation on nonlinear dynamic responses of a towed vessel in calm water. Journal of Marine Science and Engineering 8(3):219. https://doi.org/10.3390/jmse8030219.
Nam B. W, Hong S. Y, Choi Y. M, Park I. B, Lee D. Y. 2014a;June. A study on towing characteristics of a transportation barge during multi-tug operation. In : In the 24th International Ocean and Polar Engineering Conference (p. ISOPE-I-14014). ISOPE;
Nam B. W, Kim J. S, Hong S. Y. 2022;Numerical investigation on hopf bifurcation problem for nonlinear dynamics of a towed vessel in calm water and waves. Ocean Engineering 266:112661. https://doi.org/10.1016/j.oceaneng.2022.112661.
Nam B. W, Choi Y.-M, Hong S. Y. 2015;August). A study on towing characteristics of barge considering wind force. Journal of Ocean Engineering and Technology 29(4):283–290. https://doi.org/10.5574/KSOE.2015.29.4.283.
Nam B. W, Hong S. Y, Kim J. H, Choi S. K, Kim J. W. 2014b;April). Experimental and numerical investigation on towing stability of transport barge. Journal of Ocean engineering and Technology 28(2)2014. :102–110. https://doi.org/10.5574/KSOE.2014.28.2.102.
Nam B. W, Park J. Y, Hong S. Y, Sung H. G, Kim J. W. 2013, February;Numerical simulation of towing stability of barges in calm water. Journal of Ocean Engineering and Technology 27(1):67–73. https://doi.org/10.5574/KSOE.2013.27.1.067.
Sano M, Hasegawa K. 2015. A fundamental study on the ship handling simulation of tug-barge and pusher-barge systems for river service. In : Proceedings of International conference on ship and offshore technology. India. p. 141–150.
Sano M, Kawano Y, Yamamoto T, Yasukawa H. 2017;Numerical analysis of resistance acting on sea-going pusher and barge system. Journal of Ocean, Mechanical and Aerospacescience and engineering- 49(1):1–7. https://doi.org/10.36842/300jomase.v49i1.166.
Sano M, Yasukawa H, Okuda A, Hamaguchi T. 2018;Maneuverability of a pusher and barge system under empty and full load conditions. Journal of Marine Science and Technology 23(3):464–482. https://doi.org/10.1007/s00773-017-0485-3.
Wang Z, Sano M. 2025;Seakeeping performance of multi-connected pusher-barge system in regular head waves. Ocean Engineering 319:119789. https://doi.org/10.1016/j.oceaneng.2024.119789.
Yasukawa H, Hirata N, Nakamura N, Matsumoto Y. 2006;Simulations of slewing motion of a towed ship. Journal of the Japan Society of Naval Architects and Ocean Engineers 4:137–146. https://doi.org/10.2534/jjasnaoe.4.137.

Article information Continued

Fig. 1

Coordinate system of pushing simulation

Fig. 2

Various barge configurations in pushing operations

Fig. 3

Coordinate system of towing simulation

Fig. 4

Comparison of turning and zigzag maneuvers in the pushing simulation

Fig. 5

Quantitative comparison of turning and zigzag maneuver characteristics

Fig. 6

Turning trajectories with time snapshots for three representative barge configurations

Fig. 7

Comparison of turning trajectories for different barge configurations

Fig. 8

Non-dimensional turning maneuver characteristics for the 9 barge configurations

Fig. 10

Comparison of turning trajectories of towing with different towline lengths with and without skegs

Fig. 11

Effect of skeg and towline length on the turning performance of barge compared with pushing

Fig. 12

Snapshots of turning trajectories with and without skegs

Fig. 13

Effect of towline length on the time histories of towing angles and heading angle

Fig. 14

Snapshots of turning trajectories for pushing and towing conditions

Table 1

Dimensions of target vessels

Description Tug 2B barge Pushing
Length overall, LOA (m) 40 60.96 100.96
Breadth, B (m) 9 21.34 21.34
Draft, d (m) 2.2 2.74 2.74
Volume, Δ (m3) 494.7 3292.4 3787.1
Longitudinal center of buoyancy (LCB) from aft perpendicular (AP) (m) 22.23 29.44 63.24

Table 2

Pitch ratio for each configuration

Item 11BP 12BP 13BP 21BP 22BP 23BP 31BP 32BP 33BP
P 0.6121 0.7452 0.8784 0.9022 1.1743 1.3788 1.1462 1.4976 1.5574

Table 3

Comparison of hydrodynamic derivatives for three barge configurations

Item 11BP 31BP 13BP
Yβ′ 0.2055 0.3629 (+76.59%) 0.1586 (−22.8%)
Yr′ 0.00646 −0.0176 (−372.45%) −0.03974 (−715.17%)
Yβββ′ 0.4912 0.1857 (−62.19%) 0.738 (+50.24%)
Nβ′ 0.0627 0.0495 (−21.05%) 0.0439 (−29.98%)
Nr′ −0.0406 −0.1228 (+202.46%) −0.0323 (−20.44%)
Nβββ′ 0.0818 0.1976 (+141.56%) 0.0315 (−61.49%)

Table 4

Comparison of hull force, drift angle and rudder in-flow angle for three barge configurations

Item 11BP 31BP 13BP
XH′ −0.0466 −0.1014 −0.0306
FN′ 0.0152 0.0350 0.0095
β 13.8055 19.6237 15.0937
YH′ 0.0767 0.1452 0.0406
αR 14.3006 16.182 15.0709

Table 5

Effect of skeg on hydrodynamic derivatives, yaw hull moment and γ

Item w/skeg w/o skeg
Yv′ −0.4373 −0.4027
Yr′ 0.1355 0.0568
Nv′ −0.0491 −0.1160
Nr′ −0.0742 −0.0237
NH′ −0.0097 0.0303
γ 4.1836 −13.1134

Table 6

Effect of towline length on drift angle, rudder in-flow angle and sway hull force

Item Towing (LT = 2LPP) Towing (LT = 3LPP) Pushing
β 5.2641 4.2613 16.1355
αR 10.9441 11.4806 5.543
YR′ −0.0801 −0.0834 −0.0251